![]() Intel version removed as I wasn't able to test it. System run better, more stable, no bigger issues found so far. Post has been re-written on 2018.03.04 as well as all old versions and change logs removed.ĪSUS-H97M-Plus-SSDT-20180304.zip Added flew Hot Patches and other options. I believe those configuration files can be used with other ASUS H97/Z97 mainboards. Now if it posts go to BIOS, reset settings to default and save, then turn off PC, re-connect SATA cables and setup BIOS again. Tip2: If for some reason your PC stop posting during installation of OSX, try turn off PC, then disconnect all SATA cables, next power on PC. Tip: If you PC boot but hangs on denied sign try turn off and on PC and boot directly to USB flash drive instead booting anything else. After installation, install Clover, copy all required kexts, and Post Installation config file. ![]() ![]() ![]() Install macOS from USB Flash Drive using one of two USB config files, (there are simpler, less patches) 2. I'm not using HDMI or DP cable but DVI, so HDMI/DP audio unchecked and as far I know Nvidia driver doesn’t support audio for Pascal family cards yet. Sound injection patch included is in two versions, layout 1 (standard) & 99 (for SPDIF output) - chose one. When creating USB for installation, do not use SSDT-PEG0.aml from folder as system will not boot with it. PLEASE NOTE SSDT.AML not included, you need generate own using this script: You need generate new SN in SmBIOS, new SmUUID. Clover Configurator can be used to generate them for your PC. Sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/startosinstall -converttoapfs NOĬonfiguration file included has included some of the patches and removed serial number etc. Sudo /Install\ macOS\ High\ Sierra.app/Contents/Resources/startosinstall -converttoapfs NO To avoid conversion you can use this command from terminal: I would not recommend using APSF formatted partitions as my OSX installation worked much slower. The file can be extracted from /Applications/Install macOS High Sierra/Contents/Shared Support/BaseSystem.dmg -> usr/standalone/i386/ I used Clover EFI boot loader, with EmuVariableUefi-64.efi and OsxAptioFixDrv-64.efi in drivers64UEFI section of installer.ĮmuVariableUefi.efi is recommended as my Mainboard died twice with black screen (no POST) without it.ĪPFS.efi is required (to be copied to drivers64UEFI folder) if you are planning to install OSX High Sierra on SSD with APFS formatted partitions. However is suggested to use SATA0 connector if possible. My hackintosh disk is connected as SATA1 channel, so for installation I need to disable other drivers in the BIOS. I’m using default BIOS setting with common changes you can find in every install Hackintosh guide. Rest of components like memory, disk drives or optical drives are irrelevant so not listed, however separate disk drive is used for macOS installation. ASUS H97M-Plus Mainboard - Intel Core i5-4690K Processor (Haswell) - GeForce GTX 1050 Ti 4GB - Apple AirPort plus PCI-E x1 adapter. Let start from base configuration of the PC. However that would be rather short story. It took me a while to make my PC working stable. Reboot to check if everything works.I would like to share with you all my successfully working clover configuration and files as well as some suggestion which may help you. Download the following kexts Lilu - Generic kext patcher (neue Grundlage für AppleALC 1.1.x und Shiki 2.x.x), AppleALC - der dynamische AppleHDA Patcher - immer aktuell and IntelMausiEthernet.kext (as substitute for AppleIntelE1000e) and put them into /EFI/CLOVER/kexts/Otherĥ. Run the small application named Kext Utility afterwards, to recreate the Kext-Cache without those kexts.Ĥ. Delete the same files in their original location, which should be either /Library/Extensions or /System/Library/Extensionsģ. Find the kexts FakeSMC, Lilu, NvidiaGraphicsFixup, USBInjectAll, AppleIntelE1000e and copy them to the EFI partition in the folder /EFI/CLOVER/kexts/Other.Ģ. To get this things straightened out you should do the following:ġ. the install kexts on the system and not in the EFI partition. You try to load an older Lilu-Version from EFI and then the newer one, which you should find in either /Library/Extensions or /System/Library/Extensions tries to kick in which then results in your Boot problem.Īnd that is why we in this forum do not like the Beast-Tools. In your LoadedKexts.txt the Lilu.kext is in version 1.2.0 but in your /EFI/CLOVER/kexts/Other Lilu in Version 1.1.7 and AppleALC in Version 1.1.4.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |